alignment error
英 [əˈlaɪnmənt ˈerə(r)]
美 [əˈlaɪnmənt ˈerər]
安装误差；调准误差；校直误差
双语例句
- Andrew has been left wheelchair-bound after the accident
安德鲁在那次事故后就只能呆在轮椅上了。 - The Application of Square-Root Filter in Evaluation of the Transfer Alignment Error
平方根滤波算法在传递对准误差评估中的应用 - Study on positional alignment error of tubesheet workpieces 'tube holes produced with NC machine by coordinate method
用坐标法在数控机床上加工管板类工件的管孔位置度误差研究 - Study of Rapid Transfer Alignment Error Model
一种快速传递对准方法的误差模型研究 - The contact path offsets to the tip and toe of face gear tooth due to it is sensitive to the alignment error especially the error of axis shaft error in the misalignment.
啮合区域对安装误差较为敏感，特别是轴夹角误差的大小，对啮合印痕在齿面上分布的影响尤其明显，容易导致接触区域向面齿轮的大端和小端偏移。 - Analysis of system servo following error caused by alignment error of ESG
静电陀螺仪对准误差产生的系统伺服随动误差分析 - I to tell you the truth, I made two directions, alignment error.
我老实告诉你们，我犯过两次方向、路线错误。 - A design of reduced order observer is made to estimate the azimuth alignment error using the outputs of north and east accelerometers. Mean while, the state feedback method is used to improve the dynamic performance of the system.
通过构造一个降维的观测器，利用北向和东向加速度计的测量值重构平台方位对准误差角，同时利用状态反馈改善系统的动态性能。 - A study of the effect of azimuth alignment error on guidance accuracy
方位对准误差对制导精度影响的研究 - Finally, the demands for differentiating alignment error according to fit clearance as well as the proposals for improvements in the production of hydraulic elements were given.
据此提出了按配合间隙划分对中误差的要求及元件生产中的改进意见，以提高液压元件成批生产合格率和拓宽元件维修思路。 - Effect of Alignment Error to Measurement Accuracy in CCD Dimension Measuring System
CCD尺寸检测中安装误差对测量精度的影响 - This paper provided a theory foundation for improving the measure and judgement methods and the tolerance standard and the adjustment methods about the shaft alignment error of a coupling, and for advancing the accuracy of the measure and the control.
为改进对中误差的测量方法、判断方法及标准（公差）、调整方法，提高测量、控制精度提供了理论依据。 - Deducted the initial alignment error model of strap-down inertial system founding on the basic theory of it.
从捷联惯导系统初始对准的基本原理出发推导了捷联惯导系统初始对准的误差模型、给出了二位置初始对准方法。 - The measuring principle of alignment error based on laser collimator technique was introduced. The laser structure, the signal processing circuits and the data acquisition were proposed in detail.
介绍了基于激光准直原理的直线度误差自动检测方法，详细分析了激光器、传感器信号处理电路和数据采集处理系统的设计。 - A new automatic measuring system of alignment error portable laser collimator is introduced.
介绍了一种新颖的直线度误差自动测量系统&便携式激光准直仪。 - The Expression Methods of the Shaft Alignment Error of a Coupling
联轴器对中误差的表达方法 - The simulation calculation for the influence of ion beam non-uniformity in the technological system and the alignment error between substrate and mask center on device properties is carried out. The process improvement scheme is proposed according to the simulation analysis for errors.
对工艺系统中离子束不均匀度和基片与掩模板中心对准误差对器件性能的影响作了模拟计算，并根据对误差的模拟分析提出了工艺改进方案。 - The initial alignment is a key link for the output precision of strapdown inertial system and gyro drift is one of the main causes producing alignment error of the system.
在捷联惯性系统中，初始对准是影响系统输出精度的最重要环节，陀螺漂移是引起对准误差的主要原因。 - The test precision of initial measure system cannot exceed the precision limited by alignment error, so initial alignment is a very important problem in develop and application of the system.
惯性测量系统的测量精度不可能优于对准误差所限定的精度，因此初始对准是捷联惯导系统的研制与应用中一个关键的问题。 - The spectral position error at the detector derives from the alignment error, it is maximum from the alignment error at the short axis.
研究了瞄准对中误差在光谱探测器上引起的谱线位置误差，其中在椭圆短轴方向上的对中误差引起的谱线位置误差最大。 - The effect of the alignment error for structure/ mechanism reliability is analyzed. Based on the randomicity of the alignment errors, the method called "pseudo random number" is presented to simulate pseudo alignment errors.
分析了安装误差对结构/机构的影响，针对安装误差随机性的特点提出了用伪随机数生成的方法来模拟产生伪安装误差的思想； - Separation Technique of Strapdown Inertial Navigation System ( SINS) Initial Alignment Error for Tactical Surface to Air Missile
采用捷联惯性导航系统的战术导弹初始对准误差分离方法研究 - A Simplified Algorithm for Calculating the Influence of Initial Alignment Error on Inertial Guidance Error
初始对准误差对惯性制导误差影响的简化算法 - With the combination of the equal thickness interference formed by an air wedge and the CCD image-processing technique, a new method is presented to measure spatial alignment error.
将空气劈尖产生的等厚干涉与CCD图像处理技术相结合，提出了一种测量连续空间直线度误差的新方法。 - Its alignment error is small and has reached the stipulated specifications.
其对准误差小，达到了系统规定指标。 - In the process of making the error is the effect of the performance of the devices main factors, this paper analyzes coordinate error, error mutations depth, the double structure alignment error and slot modal steepness error.
分析了制作过程中引入的突变坐标误差、深度误差、双层结构对准误差及槽型陡度误差对器件性能的影响。 - The compass deviation is composed of hard iron error, soft iron error and alignment error in this thesis.
三轴磁强计的罗差主要包括硬铁误差、软铁误差和对准误差。 - Technical errors have been analyzed and simulated. The results show that the new technology is insensitive to the alignment error.
对工艺误差进行了分析和仿真，结果表明该工艺对工艺对准误差不敏感。 - Active design method of spiral bevel gear was improved by considering alignment error sensitivity of calculating point.
考虑初始计算点误差敏感性，改进了螺旋锥齿轮主动设计方法，通过计算选择安装误差敏感系数较低的初始计算点，达到减小设计齿轮副误差敏感性的目的。 - We had a error analysis of binary optical element, mainly the influence of step width error, alignment error and etching depth error on binary optical element efficiency, and we computed binary optical element efficiency in this dissertation.
分析了二元光学制作误差，包括线宽误差、对准误差和刻蚀深度误差对衍射效率的影响，并对本课题中的二元光学元件的衍射效率进行了估算。